HVAC Equipment and Engineered Air Management Systems

Stainless steel cleanroom pass box with interlocked doors

Cleanroom Equipment

Static Pass Box vs Dynamic Pass Box: How to Select the Right Transfer Solution

Pass boxes are a fundamental component of cleanroom material transfer. Selecting the wrong type can compromise contamination control. This guide explains the engineering differences between static and dynamic pass boxes and the factors that should guide your selection.

7 min readRead

Stainless steel air shower tunnel at cleanroom entrance

Cleanroom Equipment

Air Shower Design: Key Factors That Influence Cleaning Performance

An air shower removes surface particles from personnel and materials before they enter a cleanroom. Its effectiveness depends on several interrelated design factors. This guide explains the key parameters and what project teams should consider before specifying an air shower.

6 min readRead

Vertical laminar airflow clean bench in laboratory

Cleanroom Equipment

Understanding Laminar Airflow Units for Controlled Work Areas

Laminar airflow units create a controlled work zone by directing HEPA-filtered air in a uniform, unidirectional pattern across the work surface. Understanding the different configurations and their limitations is essential for correct application.

6 min readRead

Cleanroom facility layout showing personnel and material flow routes

Cleanroom Engineering

Planning Personnel and Material Movement in a Cleanroom Facility

Effective contamination control in a cleanroom depends not only on the equipment installed but on how personnel and materials move through the facility. Poor movement planning can undermine even a well-designed cleanroom system.

7 min readRead

Industrial air handling unit during factory assembly

HVAC Engineering

How to Select an Air Handling Unit for an Industrial or Commercial Project

Selecting an air handling unit involves more than matching a catalogue airflow figure to a room size. This guide covers the key technical inputs that determine whether an AHU will perform reliably in service.

8 min readRead

Cleanroom air handling unit with HEPA filtration section

HVAC Engineering

Cleanroom AHU vs Comfort AHU: Understanding the Engineering Differences

A cleanroom AHU and a comfort AHU both condition and distribute air, but they are engineered to very different standards. Understanding the differences helps project teams specify the correct equipment and avoid costly substitutions.

7 min readRead

Treated fresh air unit HVAC equipment industrial installation

HVAC Engineering

Treated Fresh Air Units and Energy Recovery: When Does a Project Need Them?

In hot and humid climates, treating outdoor air before it enters a building can significantly reduce the cooling load on the main air conditioning system. This guide explains how treated fresh air units work and when energy recovery is worth considering.

7 min readRead

Maintenance

AHU Maintenance Checklist: Filters, Coils, Fans, Drain Pans and Controls

A well-maintained AHU delivers reliable performance, maintains air quality and avoids unplanned shutdowns. This checklist covers the key inspection and maintenance tasks across daily, monthly, quarterly and seasonal intervals.

8 min readRead

Industrial PCC and MCC electrical panel assembly

Electrical Panels

PCC Panel vs MCC Panel: Functions, Applications and Selection Considerations

PCC and MCC panels are both low-voltage distribution assemblies, but they serve different functions in an electrical system. Understanding the distinction helps project teams specify the correct panel type and avoid misapplication.

7 min readRead

Electrical engineer reviewing single line diagram for LT panel design

Electrical Engineering

What Information Is Required Before Designing an LT Electrical Panel?

A well-designed LT panel begins with complete and accurate design inputs. Incomplete information at the design stage leads to revisions, delays and panels that do not meet the project requirements. This checklist covers the key inputs required before panel design can begin.

7 min readRead

APFC automatic power factor correction panel industrial installation

Electrical Panels

Understanding APFC Panels and Power-Factor Correction

Poor power factor increases the current drawn from the supply, raises distribution losses and can attract utility penalties. An APFC panel automatically corrects power factor by switching capacitor banks in response to the reactive demand of the load.

7 min readRead

Low voltage electrical panel assembly testing and verification

Standards and Compliance

Understanding IS/IEC 61439 for Low-Voltage Switchgear and Controlgear Assemblies

IS/IEC 61439 is the primary standard for low-voltage switchgear and controlgear assemblies. Understanding its key concepts helps purchasers ask the right questions and helps project teams specify panels that meet their compliance requirements.

8 min readRead

HVAC Equipment and Engineered Air Management Systems

HVAC product departments

Air Handling Units

Air Washers and Evaporative Cooling

Fresh Air, Ventilation and Exhaust

Fan Coil and Terminal Units

Heat Exchanger Coils

Air Distribution Systems

Insulated HVAC Piping

Air Filtration and Pollution Control

HVAC Automation and Controls

HVAC Engineering and Project Services

Find the right HVAC solution

Step 1 — Select a product category

HVAC Engineering Insights

Static Pass Box vs Dynamic Pass Box: How to Select the Right Transfer Solution

Air Shower Design: Key Factors That Influence Cleaning Performance

Understanding Laminar Airflow Units for Controlled Work Areas

Planning Personnel and Material Movement in a Cleanroom Facility

How to Select an Air Handling Unit for an Industrial or Commercial Project

Cleanroom AHU vs Comfort AHU: Understanding the Engineering Differences

Treated Fresh Air Units and Energy Recovery: When Does a Project Need Them?

AHU Maintenance Checklist: Filters, Coils, Fans, Drain Pans and Controls

PCC Panel vs MCC Panel: Functions, Applications and Selection Considerations

What Information Is Required Before Designing an LT Electrical Panel?

Understanding APFC Panels and Power-Factor Correction

Understanding IS/IEC 61439 for Low-Voltage Switchgear and Controlgear Assemblies